Oil Drilling Rig Package for Drilling Contractors

Oil Drilling rig package for sale worldwide meet IADC requirements to oil and gas drilling contractors

Oil drilling rig package. Sale of oil drilling rigs for drilling contracts worldwide

Drilling Rig Package for Sale/ Charter Contracts ( Secured Contracts)
Oil drilling rigs, land drilling rig, Oil gas drilling rig, Work-over drilling rig, Vertical drilling rig, Horizontal drill rig, well drilling rig, hp drilling rigs, 2000HP drilling Rig, 1000HP drilling Rig, 1500HP Drilling Rig, 3000HP drilling Rig


PYRAMID 1500 HP Land Rig National 110-UE with TDS 500 Ton Top Drive

Complete PYRAMID 1500 HP Land Rig National 110-UE oil drilling rig with top drive , mud pump, BOP package and 16000 ft drill pipes
Location: Indonesia

Drilling Depth: 16,000 ft. with 5” drill pipe, Hook Load 1,000,000 lbs w/14 Lines.
Rotary Load 1,000,000 lbs. Set back Load 800,000 lbs.
Mast: Pyramid type, open face cantilever, 156 ft.
Drawworks: National 110 UE 1500HP, 1 3/8” drill line, Powered by 2 DC, 1000 HP, 750 VDC
Auxiliary Brake: Baylor Model 6032 electric brake
Travelling Equipment: Block National 660-G-500
Top Drive: TDS-11 SA Top Drive – 500 Ton

Full Spec of this drilling rig: (Full Drilling Rig Spec)


CONTINENTAL EMSCO C-2 2000 HP Land Rig with National Oilwell PS-500A Top-Drive

Continental Emsco 2000HP oil land drilling rig with National Oilwell top drive PS-500A for long term oilfield projects with spare parts.

Rated Drilling Depth: 20,000 ft with 5'' drill pipe.

Substructure: Continental Emsco 35 ft. Hook Load: 1,000,000 lbs. Rotary Load: 1,000,000 lbs. Set Back Load: 800,000 lbs.

Mast: Continental Emsco open face 152ft.
Drawworks: Continental Emsco C-2, 1 1/2” drill line, Powered by 2 GE 752 electric motors.
Auxiliary Brake: Baylor Model 7838. Traveling Equipment: Continental Emsco TA 650.
Rotary: Continental Emsco T-3750.
Top Drive: National Oilwell PS-500A

Full Spec of this drilling rig: (Full Drilling Rig Spec)


3000 HP OILWELL E-3000 SCR Top Drive Pyramid Land Drilling Rig

3000hp drilling rig package with Oilwell E-3000 Drawworks and National Oilwell PS-500 A 500 ton Capacity Top Drive for Charter Contracts in Middle-East.

Rated Drilling Depth: 30,000 ft. with 5” drill pipe.
Substructure: Pyramid swing up 37 ft. Hook Load: 1,600,000 lbs. Rotary Load: 1,500,000 bs. Set Back Load: 800,000 lbs.
Mast: Pyramid open face cantilever 152ft
Drawworks: Oilwell E-3000 3000HP. 1 5/8” drill line, powered by 2 GE 752 electric motors.
Auxiliary Brake: Baylor Model 7838 , Traveling Equipment: Block Oilwell -650 Ton, Rotary: Oilwell B-375. Powered by 1 GE 752 electric motor
Top Drive: National Oilwell, PS-500 A Capacity 500 ton.

Full Spec of this drilling rig: (Full Drilling Rig Spec)


2 Units 2000Hp Oil Drilling Rigs ( Brand New Drilling Rig Package )

Brand New Rigs from U.S.A.

Location: United Arab Emirates

Mast : 147 FT at 1,300,000LBS, Engines ( Cat 3412, and Cat 3512 DITTA Engines) , Cat 3512C Tier lll Generators
Hydrill BOP Package rated @ 10,000PSI , Rotary Tables
12 New Garden Denver PZ11 Mud pumps rated @ 1600HP, New Fluid Ends, Brand New SCR Units,
4 Units Brand New Varco TDS-11 Top Drives rated at 500 Ton capacity.
( Available to add to this package, 2 months delivery time )
Substructures: 32Ft with 1,300,000 LBS Capacity,

New Drilling Rig Package can be fully assembled in UAE or delivered directly to the project.

Owners willing to put the rigs in to drilling project contracts based in : GCC Countries, Iraq, or Libya

Full Spec of this drilling rig: (Full Drilling Rig Spec)


NATIONAL 110 UE 1500HP Drilling Rig, Single Drum Drawworks, 4-Bay SCR Unit

No DRILL PIPE, No DRILL COLLARS

DRAWWORKS:
NATIONAL 110 UE 1500HP Single Drum Drawworks, LEBUS Grooved

Mud Pumps
Two (2) Weatherford MP-16, 1600 HP packages each with master skid, two (2) remanufactured 752 DC series wound traction motors, drive sheaves, belts, belt guards, charge pump and liner wash system.

Full Spec of this drilling rig: (Full Drilling Rig Spec)


2000 HP Oilwell E-2000 Diesel Electric Oil Rig

Drawworks:
Oilwell E-2000, 2000 HP, grooved for 1-3/8” drill line with two (2) refurbished G.E. 752 series wound DC traction motors, Baylor 7838 Auxiliary Brake, make-up and break-out catheads.

Mud Pumps:
Two (2) Weatherford MP-16, 1600 HP packages each with master skid, two (2) refurbished G.E. 752 series wound DC traction motors, drive sheaves, belts, belt guards, charge pump, liner wash system, etc.

Mast:
152’, 1,000,000#SHL with crown containing six (6) main cluster sheaves and one (1) fastline sheave. Mast to include racking board, raising lines, etc.

Substructure:
30’ High Self-Elevating, 1,000,000# casing, 600,000# setback, complete with two (2) sets of stairs from drill floor to ground, one (1) set of stairs from drill floor to water tank, v-door, catwalk, mousehole and rathole.

Full Spec of this drilling rig: (Full Drilling Rig Spec)


SUPERIOR 700 UE Drilling Rig / SCR / With over 7000ft 4 1/2 Drill pipe

- Available for Inspection and Delivery

SUPERIOR 700 UE Drilling Rig, Location: USA

DRAWWORKS : Superior 700 D/D UE
Drawworks 800 HP 18"x 40" drum, 42"x 8-3/8" Brake Bands, p/b GE 752 (1,000 HP) , National 27-1/2" Rotary Table. All above mounted on skid w/covered roof.

MAST
Dreco 133' x 428,000 # (SN E9186-698) 18.5ft leg spread, gross nominal capacity of 600,000 Lbs., Crown c/w Five (5) 1-1/8" sheaves, One (1) F. Mast comes with CAT-4 inspection, National 250-Ton block-hook combination, 300T National Swivel (N-69).

SUBSTRUCTURE
Dreco Sling-Shot Substructure 14' 7", GL-Rotary Beams 16' 7" with Skidding System c/w Two (2) Lantec hydraulic winches, hydraulic operating system mounted on top Doghouse. Substructure comes with CAT-4 inspection. Derrick Stand 8' x 10'x 21'.

Full Spec of this drilling rig: (Full Drilling Rig Spec)

Oil News Crude Oil price Drilling Formula Rig Count Oil and Gas Events Training

Cooper Workover/Well Service/Drilling Rig
Built and Refurbished in USA.

Location: USA

Drawworks System:
Main Drum
Brake rim diameter x width 46" dia x 12" wide
Barrel diameter x width 20" dia x 41" wide [excluding lebus]
Model, clutch PO-330
Maximum fastline pull 52,000 lbf
1 non permit load.

Full Spec of this drilling rig: (Full Drilling Rig Spec)


Newly Refurbished 2000 HP National 1320 Drilling Rig Package

DRAWWORKS ( Refurbished )
Model: National 1320 UE, Rated Horsepower: 2000 HP
Drive Motors: Two (2) 1250 HP, Joliet Traction Motors with 10hp Blowers
Auxiliary Brake: Eaton (or Equal) 336 Disc Brakes
Brake Cooling: 50 bbl water tank, with 4 x 3 x 13 centrifugal pump and 30 hp electric driver

SUB STRUCTURE ( Refurbished with API certificate)
Model: Pyramid Self- Elevating Substructure
Drill Floor Height: 25 ft. Casing Capacity: 1,000,000 lbs. Setback Capacity: 600,000 lbs.
Total Capacity: 1,600,000 lbs
.

Full Spec of this drilling rig: (Full Drilling Rig Spec)


1000HP Rig package Trailer Rig

Location: Texas / USA
Brand New Rig package, Can be complete in 150 Days

Drawworks:
1000HP, grooved for 1-1/8” drill line with two (2) new Detroit series 60 Engines and water cooled Auxiliary Brake.

Mud Pumps:
Two (2) Weatherford MP-10, 1000 HP packages each with master skid, new Caterpillar 3508 engines

Full Spec of this drilling rig: (Full Drilling Rig Spec)


1200HP PARCO OIME Diesel Electric Rig with SCR System

Drawworks:
1200 HP, OIME SL-7 grooved for 1-1/4” drill line with two (2) new 752 Type series wound DC traction motors and Auxiliary Brake.

Mud Pumps:
Two (2) Weatherford MP-16, 1600 HP packages each with master skid, two (2) remanufactured 752 DC series wound traction motors, drive sheaves, belts, belt guards, charge pump and liner wash system.

Mast:
136’, 750,000#SHL with crown containing six (6) main cluster sheaves and one (1) fast-line sheave. Mast to include racking board, raising lines, etc.

Substructure:
21’ Self-Elevating, 638,000# casing, 487,000# setback, complete with two (2) sets of stairs from drill floor to ground, one (1) set of stairs from drill floor to mud system, v-door, catwalk, mousehole and rathole.

Full Spec of this drilling rig: (Full Drilling Rig Spec)


New Build 2000HP ZJ70DB AC Drive Electric Drilling Rig with Top Drive

Hook load: 1,000,000 lbs, 500 US ton (4500KN) with 12 lines
• Setback capacity: 386000 lbs, 193 US ton
• Simultaneous hook load and setback capacity: 1,376,000 lbs, 688 US ton (6120KN)
• Static Rotary beam capacity: 1,000,000 lbs, 500 US ton.
• Mast type: K Type mast open fronted 147.6 ft, adjustable monkey board 74ft-87ft with SALA Geronimo Escape system
• Substructure type: Parallelogram swing up integrated raising substructure with rig floor
• Depth rating: 4 ½” Drill pipe: 22,967 ft (7000M), 5” DP 19,686 ft (6000M)

Full Spec of this drilling rig: (Full Drilling Rig Spec)


1500 HP TSM AC Drawworks Drilling

1500 HP TSM Drilling Rig with AC Drive Drawworks and National Oilwell Varco TDS11 Top Drive for Deep Well Drilling

Drawworks : Drawworks Model: TSM 1500 AC, Capacity: 750,000 lbs w/ 12 Lines

Top Drive: National Oilwell Varco TDS11, AC 500 Ton, 37,500 ft-lbs, 800 HP

Full Spec of this drilling rig: (Full Drilling Rig Spec)



How Drilling Works

Main Oil Drilling Equipments

Depending upon the remoteness of the drill site and its access, equipment may be transported to the site by truck, helicopter or barge. Some rigs are built on ships or barges for work on inland water where there is no foundation to support a rig (as in marshes or lakes). Once the equipment is at the site, the rig is set up. Here are the major systems of a land oil rig:

Power system
large diesel engines - burn diesel-fuel oil to provide the main source of power
electrical generators - powered by the diesel engines to provide electrical power

Mechanical system - driven by electric motors
hoisting system - used for lifting heavy loads; consists of a mechanical winch (drawworks) with a large steel cable spool, a block-and-tackle pulley and a receiving storage reel for the cable turntable - part of the drilling apparatus

Oil and Gas Tenders :

Rotating equipment - used for rotary drilling
swivel - large handle that holds the weight of the drill string; allows the string to rotate and makes a pressure-tight seal on the hole
kelly - four- or six-sided pipe that transfers rotary motion to the turntable and drill string
turntable or rotary table - drives the rotating motion using power from electric motors
drill string - consists of drill pipe (connected sections of about 30 ft / 10 m) and drill collars (larger diameter, heavier pipe that fits around the drill pipe and places weight on the drill bit)
drill bit(s) - end of the drill that actually cuts up the rock; comes in many shapes and materials (tungsten carbide steel, diamond) that are specialized for various drilling tasks and rock formations

Casing - large-diameter concrete pipe that lines the drill hole, prevents the hole from collapsing, and allows drilling mud to circulate

Circulation system - pumps drilling mud (mixture of water, clay, weighting material and chemicals, used to lift rock cuttings from the drill bit to the surface) under pressure through the kelly, rotary table, drill pipes and drill collars
- Pump - sucks mud from the mud pits and pumps it to the drilling apparatus
- Pipes and hoses - connects pump to drilling apparatus
- Mud-return line - returns mud from hole
- Shale shaker - shaker/sieve that separates rock cuttings from the mud
- Shale slide - conveys cuttings to the reserve pit
- Reserve pit - collects rock cuttings separated from the mud
- Mud pits - where drilling mud is mixed and recycled
- Mud-mixing hopper - where new mud is mixed and then sent to the mud pits

Derrick - support structure that holds the drilling apparatus; tall enough to allow new sections of drill pipe to be added to the drilling apparatus as drilling progresses

Blowout preventer - high-pressure valves (located under the land rig or on the sea floor) that seal the high-pressure drill lines and relieve pressure when necessary to prevent a blowout (uncontrolled gush of gas or oil to the surface, often associated with fire)

Oil Drilling Process - Setting up Drilling Rig

The drilling team sets up the rig and starts the drilling operations. First, from the starter hole, they drill a surface hole down to a pre-set depth, which is somewhere above where they think the oil trap is located. There are five basic steps to drilling the surface hole:

Place the drill bit, collar and drill pipe in the hole.
Attach the kelly and turntable and begin drilling.
As drilling progresses, circulate mud through the pipe and out of the bit to float the rock cuttings out of the hole.
Add new sections (joints) of drill pipes as the hole gets deeper.
Remove (trip out) the drill pipe, collar and bit when the pre-set depth (anywhere from a few hundred to a couple-thousand feet) is reached.
Once they reach the pre-set depth, they must run and cement the casing -- place casing-pipe sections into the hole to prevent it from collapsing in on itself. The casing pipe has spacers around the outside to keep it centered in the hole.

The casing crew puts the casing pipe in the hole. The cement crew pumps cement down the casing pipe using a bottom plug, a cement slurry, a top plug and drill mud. The pressure from the drill mud causes the cement slurry to move through the casing and fill the space between the outside of the casing and the hole. Finally, the cement is allowed to harden and then tested for such properties as hardness, alignment and a proper seal.

Drilling continues in stages: They drill, then run and cement new casings, then drill again. When the rock cuttings from the mud reveal the oil sand from the reservoir rock, they may have reached the final depth. At this point, they remove the drilling apparatus from the hole and perform several tests to confirm this finding:

Well logging - lowering electrical and gas sensors into the hole to take measurements of the rock formations there
Drill-stem testing - lowering a device into the hole to measure the pressures, which will reveal whether reservoir rock has been reached
Core samples - taking samples of rock to look for characteristics of reservoir rock
Once they have reached the final depth, the crew completes the well to allow oil to flow into the casing in a controlled manner. First, they lower a perforating gun into the well to the production depth. The gun has explosive charges to create holes in the casing through which oil can flow. After the casing has been perforated, they run a small-diameter pipe (tubing) into the hole as a conduit for oil and gas to flow up the well.

A device called a packer is run down the outside of the tubing. When the packer is set at the production level, it is expanded to form a seal around the outside of the tubing. Finally, they connect a multi-valved structure called a Christmas tree to the top of the tubing and cement it to the top of the casing. The Christmas tree allows them to control the flow of oil from the well.

Once the well is completed, they must start the flow of oil into the well. For limestone reservoir rock, acid is pumped down the well and out the perforations. The acid dissolves channels in the limestone that lead oil into the well. For sandstone reservoir rock, a specially blended fluid containing proppants (sand, walnut shells, aluminum pellets) is pumped down the well and out the perforations. The pressure from this fluid makes small fractures in the sandstone that allow oil to flow into the well, while the proppants hold these fractures open. Once the oil is flowing, the oil rig is removed from the site and production equipment is set up to extract the oil from the well.

Rigsworld worldwide news

Extracting the Oil from Oil Well after Drilling Process
After the rig is removed, a pump is placed on the well head.

In the pump system, an electric motor drives a gear box that moves a lever. The lever pushes and pulls a polishing rod up and down. The polishing rod is attached to a sucker rod, which is attached to a pump. This system forces the pump up and down, creating a suction that draws oil up through the well.

In some cases, the oil may be too heavy to flow. A second hole is then drilled into the reservoir and steam is injected under pressure. The heat from the steam thins the oil in the reservoir, and the pressure helps push it up the well. This process is called enhanced oil recovery.

With all of this oil-drilling technology in use, and new methods in development, the question remains: Will we have enough oil to meet our needs? Current estimates suggest that we have enough oil for about 63 to 95 years to come, based on current and future finds and present demands.

Drilling Rigs for worldwide Sale/ Day Rate Contract
(BASE ON SECURED CONTRACTS ONLY)
1000HP, 1500HP, 2000HP, 3000HP Land Drilling Rigs
for Worldwide Drilling Charter Contract
Generators Mud Pumps

Drilling Rig

Description: Oil drilling rig package. Sale of oil drilling rigs for drilling contracts worldwide

Tags: drilling rig, drilling rigs, drilling rig contractor, land rig sale, 2000 hp land rig, hp drilling rigs, oil drilling rigs, rotary table drilling rigs, rotary land drilling rig, drilling rig package, refurbished oil rig